An image of the Spotlight Cam 4K Plus, mounted on an exterior wall of a house with the lights turned on.

Installing Ring Spotlight Camera 4K Plus Wired

Download the user manual for Ring Spotlight Camera 4K Plus Wired

Hardware included

Hardware parts: a round cap, an oval cap, a short screw B, and a long screw C with a wall anchor


Tools needed

An illustration of a Phillips-head screwdriver.

Phillips-head screwdriver

An illustration of a caulk gun.

Caulk gun

A cordless power drill with a drill bit

Drill with a 6 mm masonry bit (optional)


Junction box

WARNING: Risk of electrical shock. Installation and wiring must be performed by a licensed electrician in Australia and New Zealand, and may be required in other countries. Refer to your local laws and building regulations before performing electrical work; permits and/or professional installation may be required by law.

CAUTION: Risk of fire. Do not install near combustible or flammable surfaces. The Hardwired Kit must be installed on a wall or eave.

NOTE: If your power system is classified as OVC III, please check the building “Distribution Panel”, Ex switch panel has installed Surge Protectors. Ensure that the surge protector is an IEC 61051-2 certified Surge Protector to reduce Mains Transient Voltage to Overvoltage Category II (2500 V pk or lower) before connecting to all AC Inputs. If there is no Surge Protector, do not install Hardwired Kit without one.

Before you begin installing your Hardwired Kit, make sure that you’re following safety code standards.

  • Turn off power at the consumer unit before installing.
  • Verify that the supply voltage is correct. Connect product to a 100~240 VAC 50/60 Hz power source.
  • The earth wire must be connected to the product. DO NOT INSTALL if a working earth connection is not available.
  • Do not connect this product to a dimmer switch or timer.

1.

Shut off power at the breaker.

An illustration of a circuit breaker panel with a warning symbol.

2.

Feed wire through grommet.

NOTE: Use a minimum 18AWG or higher round 3-core cable with outer diameter of 6-7 millimeters and core diameter of 0.75-1 millimeters.

Back of the wired mount with an arrow showing a cable feeding up through the grommet

3.

Tighten wire fastener screws.

WARNING: The pressing plate should be over the cable insulation, and not over the individual wires.

A screwdriver turning a wire fastener screw on the back of the wired mount

4.

Use level and mark screw holes.

A pencil marking the screw hole positions on the wired mount, with a level at the top

5.

Install junction box.

On stucco, brick, or concrete, use a 6 mm masonry bit to drill holes for the included wall anchors.

Wired mount with screwdriver and screw C, plus icons for drilling masonry or screwing into wood

6.

Cover screws with rubber caps.

Wired mount with arrows pointing to screw holes and a rubber cap beside a screw

Optional: Use the built-in hooks to hold the S-hook.

Wired mount hanging from an S-hook on the built-in hook, with an arrow pointing to the hook

7.

Connect wires.

Earth screw, washers and wire loops stacked on a screw, with icons for the mount and the house earth

Fasten earth screw with a minimum torque of 0.4N/m.

Screwdriver fastening the earth screw on the wired mount while the cover hangs below

Connect the brown (L) and blue (N) wires.

NOTE: If ever needed to remove wires: Remove the brown (L) and blue (N) wires. Then, remove the yellow wired mount bonding conductor wire and the home protective earthing conductor wire.

WARNING: Please follow standard electrical code in your country. Depending on the age of the home, the wires may not match the colours shown below. Please consult a qualified electrician in your area if you are unsure or uncomfortable installing or uninstalling.

Brown, blue and yellow wires connected inside the wired mount, with an English colour legend

8.

Tuck wires and install wired mount.

Wired mount with wires entering a junction box, screwdriver, screw and arrows to the box

9.

Tighten screws until fully sealed.

Then, tighten the screws into the wired mount until the foam backing fully seals the junction box to prevent water from entering. (1.37-1.47N/m of torque force)

Front of the wired mount with a screwdriver on one screw hole and four screw positions marked B

10.

Apply a weatherproof silicone caulk or sealant around the outside where the wired mount and wall meet to prevent water from entering the junction box.

An illustration of a caulk gun applying sealant around the wired mount.

11.

Apply cosmetic screw plugs.

An illustration of the cosmetic screw plugs on a circular wired mount.

Camera installation

1.

Tighten the included hex joint onto the back of your camera, ensuring the UP arrow is pointing up.

An illustration of a hex joint beside the camera and a screwdriver at its back.

2.

Remove the rubber plug from your camera’s power port.

NOTE: Store the rubber plug in a safe place. Reinsert it into the power port when not in use.

An illustration of a rubber plug being removed from the camera power port.

3.

Plug the USB-C cable on the Hardwired Mount into your camera, ensuring it is fully inserted.

An illustration of a USB-C cable connecting the wired mount to the camera.

4.

Align the locking indicators on the hex joint and the Hardwired Mount and insert.

An illustration of locking indicators aligned between the camera and wired mount.

5.

Turn until your camera locks in place.

An illustration of the camera turning on the wired mount to lock into place.

6.

Tighten the security screw.

An illustration of a screwdriver tightening a security screw beneath the mounted camera.

7.

Install your camera’s decorative cover by sliding until you hear a click to secure.

An illustration of a decorative cover sliding onto the mounted camera.

8.

Adjust your camera’s position, if necessary.

An illustration of the camera being adjusted within its circular mount.

9.

Must apply proper silicone or caulk around the junction box knockouts, between the junction box and Hardwired Mount, and between the junction box and mounting surface to seal any gaps.

An illustration of a caulk gun applying sealant around the camera and wired mount.

10.

Restore power at the consumer unit.

An illustration of a circuit breaker panel with a warning symbol.

Last updated 3 days ago