An image of the Spotlight Cam 4K Plus, mounted on an exterior wall of a house with the lights turned on.

Installing Ring Spotlight Camera 4K Plus PoE

Download the user manual for Ring Spotlight Camera 4K Plus PoE

Hardware included

An illustration of a long screw labeled A, a shorter screw labeled B and a wall anchor labeled C.

Tools needed

An illustration of a drill.

Drill with a 6 mm masonry bit (optional)

An illustration of a Phillips-head screwdriver.

Philips-head screwdriver

An illustration of a caulk gun.

Caulk gun


1.

Choose a location.

NOTE: Before installation, ensure your Power over Ethernet (PoE) switch or injector capable of PoE+ is active and connected to a functioning Category 5 or above Ethernet cable.

An illustration of two cameras side by side, one mounted on a wall and one mounted on a ceiling.

2.

Ensure your Ethernet cable does not have a pusher or strain relief.

An illustration of a plain Ethernet plug with a check mark, and plugs with a pusher or strain relief marked X.

Wall installation

1.

Slide the mounting plate on your camera’s native mount opposite to the UP arrow to remove.

An illustration of the camera's mounting plate being removed by sliding it in the opposite direction of the UP arrow.

2.

Use the mounting plate to mark screw holes on the wall.

An illustration of a pencil marking screw holes by using the mounting plate as a guide.

A. Routing Ethernet cable through the wall

3a.

If routing the Ethernet cable through the wall, feed the Ethernet cable through the included grommet, then the mounting plate.

An illustration of an Ethernet cable coming out of the wall and passing through a grommet and the mounting plate.

4a.

Install the mounting plate with the UP arrow pointing up.

On stucco, brick, or concrete, use a 6 mm masonry bit to drill holes for the included wall anchors.

An illustration of a screwdriver driving screw B through the mounting plate into the wall, UP arrow pointing up.A drill, anchor C and screw B for masonry, and screw B going into a wood block.

B. Routing Ethernet cable through the side

3b.

If routing the Ethernet cable through the side, align the grommet, spacer, and mounting plate, then route the Ethernet cable through the slot in the spacer and the mounting plate.

NOTE: The Ethernet cable should not feed through the grommet.

An Ethernet cable routed through the side slot of the spacer and the mounting plate.

4b.

Install the mounting plate over the spacer with the UP arrow pointing up.

On stucco, brick, or concrete, use a 6 mm masonry bit to drill holes for the included wall anchors.

A screwdriver driving screw A through the mounting plate and spacer into the wall.A drill, anchor C and screw A for masonry, and screw A going into a wood block.

5.

Plug the Ethernet cable into the back of the mount.

An Ethernet cable being plugged into the port on the back of the mount.

6.

Slide the mount onto the mounting plate until you hear a click.

The mount sliding onto the mounting plate on a wall.

7.

Tighten the screw to secure.

A screwdriver tightening the screw on the side of the mount on a wall.

Ceiling installation

1.

Slide the mounting plate on your camera’s native mount opposite to the UP arrow to remove.

An illustration of the camera's mounting plate being removed by sliding it in the opposite direction of the UP arrow.

2.

Use the mounting plate to mark screw holes on the ceiling.

An illustration of a pencil marking screw holes by using the mounting plate as a guide.

A. Routing Ethernet cable through the ceiling

3a.

If routing the Ethernet cable through the ceiling, feed the Ethernet cable through the included grommet, then the mounting plate.

An Ethernet cable coming down from the ceiling through a grommet and the mounting plate.

4a.

Install the mounting plate with the UP arrow pointing opposite to your desired viewing direction.

On stucco, brick, or concrete, use a 6 mm masonry bit to drill holes for the included wall anchors.

A screwdriver driving screw B up through the mounting plate into the ceiling.A drill, anchor C and screw B for masonry, and screw B going into a wood block.

B. Routing Ethernet cable through the side

3b.

If routing the Ethernet cable through the side, align the grommet, spacer, and mounting plate, then route the Ethernet cable through the slot in the spacer and the mounting plate.

NOTE: The Ethernet cable should not feed through the grommet.

An Ethernet cable routed through the side slot between the ceiling spacer and mounting plate.

4b.

Install the mounting plate over the included spacer with the UP arrow pointing opposite to your desired viewing direction.

On stucco, brick, or concrete, use a 6 mm masonry bit to drill holes for the included wall anchors.

A screwdriver driving screw A up through the mounting plate and spacer into the ceiling.A drill, anchor C and screw A for masonry, and screw A going into a wood block.

5.

Plug the Ethernet cable into the back of the mount.

An Ethernet cable being plugged into the port on the back of the mount.

6.

Slide the mount onto the mounting plate until you hear a click.

The mount sliding up onto the mounting plate on a ceiling.

7.

Tighten the screw to secure.

A screwdriver tightening the screw on the side of the mount on a ceiling.

Camera installation

1.

Refer to your camera’s setup guide to remove the native mount and rubber cap.

Information icon with open book design

2.

Tighten the included hex joint onto the back of your camera, ensuring the UP indicator is pointing up.

A hex joint fitted to the back of the camera, UP indicator up, and tightened with a screwdriver.

3.

Refer to your camera setup guide to remove the rubber plug from your camera’s power port, if necessary.

Information icon with open book design

4a.

Plug the USB-C cable on the mount into your camera, ensuring it is fully inserted.

The mount's USB-C cable being plugged into the back of a camera beside a wall mount.

4b.

If installing on the ceiling, route the USB-C cable on the mount from the bottom of the ball joint, then plug it into your camera, ensuring it is fully inserted.

The mount's USB-C cable being plugged into the back of a camera below a ceiling mount.

5.

Align the locking indicators on the hex joint and the mount and insert.

The camera's hex joint being inserted into the mount, with close-ups of the alignment marks.

6.

Turn until your camera locks in place.

The camera being turned upright to lock in place, with a close-up of the lock indicator.

7.

Tighten the security screw.

A screwdriver above the mount tightening the security screw that holds the camera.

8.

Install your camera’s decorative cover by sliding until you hear a click to secure.

A decorative cover sliding up onto the back of a wall-mounted camera.

9.

Loosen the screw on the metal collar to adjust your camera’s position, if necessary.

A screwdriver below the mount loosening the metal collar screw to adjust the camera.

10.

Apply a weatherproof silicone caulk or sealant around the mount and between the mount and mounting surface to seal any gaps.

A caulk gun applying sealant around the base of the mount where it meets the surface.

Last updated 3 days ago