Safety and compliance information for Battery Video Doorbell Plus (2nd Generation)

IMPORTANT PRODUCT INFORMATION

SAFETY INFORMATION

READ ALL SAFETY INFORMATION BEFORE USING THE DEVICE. FAILURE TO FOLLOW THESE SAFETY INSTRUCTIONS COULD RESULT IN FIRE, ELECTRIC SHOCK, OR OTHER INJURY OR DAMAGE.

Installation by a qualified electrician may be required in your area. Refer to your local laws and building codes before performing electrical work; permits and/or professional installation may be required by law.

Please consult a qualified electrician in your area if you are unsure or uncomfortable in performing the installation.

CAUTION: Risk of fire. Do not install near combustible or flammable surfaces.

HANDLE WITH CARE. Your device contains lithium-ion rechargeable batteries. Use only the provided charger and charging cables. Use of an unqualified battery or charger may present a risk of fire, explosion, shock, chemical leakage, or other hazard. If battery replacement becomes necessary, use only a new lithium-ion rechargeable battery expressly qualified for use with your device.

Keep all batteries out of reach of children. Do not attempt to open, disassemble, modify, or remanufacture the battery, attempt to insert foreign objects into the battery, or immerse or expose it to water, other liquids, fire, explosion, or other hazards. To avoid short-circuiting a battery, do not allow battery terminals to touch metallic conductive objects or other battery terminals. Avoid dropping the device or battery. Do not crush or puncture the battery. Watch for signs of faulty batteries, including swelling, dents, and tears in the battery wrapper. If you suspect damage to the device or battery, do not attempt repair. Instead, remove batteries from your device and contact Ring Customer Service for assistance.

Only charge your batteries inside a building, in a dry state and using the supplied charging cable.

OTHER SAFETY CONSIDERATIONS

Your device can withstand outdoor use and contact with water under certain conditions. However, your device is not intended for underwater use and may experience temporary effects from exposure to water. Do not immerse your device in water.

Do not spill any food, oil, lotion, or other abrasive substances on your device. Do not expose your device to pressurized water, high velocity water, or extremely humid conditions (such as a steam room). Do not expose your device or batteries to salt water or other conductive liquids. To protect against electric shock, do not place cord, plug, or device in water or other liquids.

If your device gets wet from immersion in water or high pressure water, carefully disconnect all cables without getting your hands wet and wait for them to dry completely before powering it on again. Do not attempt to dry your device or batteries with an external heat source, such as a microwave oven or a hair dryer.

To avoid risk of electric shock, do not touch your device or batteries or any wires connected to your device during a lightning storm while your device is powered. If your device or batteries appears to be damaged, discontinue use immediately.

Use only accessories supplied with your device, or specifically marketed for use with your device, to power your device. Use of third-party accessories may impact your device’s performance. In limited circumstances, use of third-party accessories may void your device’s limited warranty. In addition, use of incompatible third-party accessories may cause damage to your device or the third-party accessory. Read all safety instructions for any accessories before using with your device.

WARNING: Small parts contained in your device and its accessories may present a choking hazard to small children.

CAUTION: When mounting this device in elevated locations, use precautions to ensure that the device does not fall and harm bystanders.

SAFELY CONNECTING YOUR BATTERY VIDEO DOORBELL PLUS (2ND GENERATION) TO YOUR HOME’S ELECTRICAL WIRING

If you install the Battery Video Doorbell Plus (2nd Generation) where a doorbell is already in use and you connect the Battery Video Doorbell Plus (2nd Generation) to your home’s doorbell electrical wiring, you must turn off the existing doorbell’s power source at your home’s circuit breaker or fuse and test that the power is off BEFORE removing the existing doorbell, installing the Battery Video Doorbell Plus (2nd Generation), or touching electrical wires. Failure to turn off circuit breaker or fuse so could result in FIRE, ELECTRIC SHOCK, or OTHER INJURY or DAMAGE.

More than one disconnect switch may be required to turn off the equipment before servicing. To test whether you have successfully de-energized your existing doorbell’s power source, press your doorbell several times to confirm that the power is off.

If the electrical wiring in your home does not resemble any of the diagrams or instructions provided with Battery Video Doorbell Plus (2nd Generation), if you encounter damaged or unsafe wiring, or if you are unsure or uncomfortable in performing this installation or handling electrical wiring, please consult a qualified electrician in your area.

Please avoid touching exposed wires to one another.

PROTECTION AGAINST WATER

If your device is dropped or otherwise damaged, the waterproofing of the device may be compromised.

PRODUCT SPECIFICATIONS

Device Name: Battery Video Doorbell Plus (2nd Generation)

Model number: 5DCFAB

Electrical Rating: 8-24V～, 50/60Hz, 5VA or 24V⎓420mA

Operating Temperature Range: -4°F to 122°F (-20°C to 50°C)

Power Consumption

Note: The device automatically goes into Networked Standby after 20 minutes of inactivity.

FOR USA CUSTOMERS

Electronic Labeling for Battery Video Doorbell Plus (2nd Generation) Certification information regarding your device can be found electronically via the Ring app in the device’s Settings Menu under Device Health > Safety and Compliance Information.

Supplier’s Declaration of Conformity

Device Name: Battery Video Doorbell Plus (2nd Generation)

Model: 5DCFAB

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Responsible Party and Party issuing Supplier’s Declaration of Conformity: Ring LLC, 12515 Cerise Ave Hawthorne, CA, 90250 U.S.A.www.ring.com / legal@ring.com NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Caution, pursuant to Section 15.21 of the FCC rules, user changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with FCC radio frequency radiation exposure limits set forth for an uncontrolled environment. Information is on file with the FCC and can be found by inputting such Product’s FCC ID (which can be found on the device) into the FCC ID Search form available at fcc.gov/oet/ea/fccid. The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other product antenna or transmitter.

FOR CANADIAN CUSTOMERS

Innovation, Science and Economic Development Canada (ISED) Compliance

This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions: (1) This device may not cause interference. (2) This device must accept any interference, including interference that may cause undesired operation of the device.

INFORMATION REGARDING EXPOSURE TO RADIO FREQUENCY ENERGY

This equipment complies with IC RSS-102 RF exposure limits set forth for an uncontrolled environment.

This device for operation in the band 5150–5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems.

This equipment should be installed and operated with a minimum distance of 20 cm between the radiator and your body.

RECYCLING YOUR DEVICE PROPERLY

In some areas, the disposal of certain electronic devices is regulated. Make sure you dispose of, or recycle, your device in accordance with your local laws and regulations. For information about recycling your device, go to www.amazon.com/devicesupport.

ADDITIONAL SAFETY AND COMPLIANCE INFORMATION

Additional safety, compliance, recycling and other important information regarding your device can be found at: www.ring.com/legal

TERMS AND POLICIES

By purchasing or using the product, you agree to the Terms of Service found at ring.com/terms. For other applicable policies, visit ring.com/legal.

LIMITED WARRANTY

For information on the Limited Warranty, visit ring.com/legal.