Safety and Compliance Information for Hardwired Kit
IMPORTANT PRODUCT INFORMATION
SAFETY INFORMATION
READ ALL SAFETY INFORMATION BEFORE USING THE DEVICE. FAILURE TO FOLLOW THESE SAFETY INSTRUCTIONS COULD RESULT IN FIRE, ELECTRIC SHOCK, OR OTHER INJURY OR DAMAGE.
WARNING: Electrical shock hazard. Disconnect power to installation area at your circuit breaker or fuse box before beginning installation. Always use caution when handling electrical wiring.
Make sure to follow all installation instructions
Installation by a qualified electrician may be required in your area. Refer to your local laws and building codes before performing electrical work; permits and/or professional installation may be required by law.
Please consult a qualified electrician in your area if you are unsure or uncomfortable in performing the installation.
Your Hardwired Kit must be installed on a 4“ round UL-listed weatherproof electrical box when installed outdoors.
CAUTION: Risk of fire. Do not install near combustible or flammable surfaces.
CAUTION: To reduce the risk of electrical shock, DO NOT open the unit. Some products may have user serviceable parts and should only be opened in accordance with Ring repair instructions. Refer to customer support for any repairs.
OTHER SAFETY CONSIDERATIONS
Your hardwired kit can withstand outdoor use and contact with water under certain conditions. However, your hardwired kit is not intended for underwater use and may experience temporary effects from exposure to water. Do not immerse your hardwired kit in water. Do not spill any food, oil, lotion, or other abrasive substances on your hardwired kit. Do not expose your hardwired kit to pressurized water, high velocity water, or extremely humid conditions (such as a steam room). Do not expose your hardwired kit to salt water or other conductive liquids. To protect against electric shock, do not place cord, plug, or hardwired kit in water or other liquids. Do not attempt to dry your hardwire kit with an external heat source, such as a microwave oven or a hair dryer. To avoid risk of electric shock, do not touch your hardwire kit or any wires connected to your hardwired kit during a lightning storm while your device is powered. If your hardwire kit or device appears to be damaged, discontinue use immediately.
WARNING: Small parts contained in your hardwired kit may present a choking hazard to small children.
Do not cut any wires with factory installed wire connectors or remove the wire connectors.
Do not install on circuits feeding motor loads such as kitchen appliances, HVAC equipment, washer/ dryer or garage door openers.
Do not install when it is raining.
CAUTION: When mounting this hardwire kit in elevated locations, use precautions to ensure that the device does not fall and harm bystanders.
SAFELY CONNECTING YOUR HARDWIRED KIT TO YOUR HOME’S ELECTRICAL WIRING WARNING! You must disconnect the power source at the home’s circuit breaker or consumer unit and test that the power is off BEFORE removing an existing light fixture, installing the device, or touching electrical wires. It is extremely important to adhere to this safety precaution, especially if any natural gas, petrol fumes, or other potentially explosive fumes may be present in the vicinity. DO NOT USE your device if power has not been disconnected. Failure to turn off circuit breaker or consumer unit could result in EXPLOSION, FIRE, ELECTRIC SHOCK, DEATH, OTHER INJURY or PROPERTY DAMAGE.
BEFORE installing your device with the hardwired kit, review the diagrams and instructions provided. If the electrical wiring in the home does not resemble any of these diagrams or instructions, if you encounter damaged or unsafe wiring, or if you are unsure or uncomfortable in performing this installation or handling mains electrical wiring, please consult a qualified electrician. Verify that the supply voltage is correct. Connect fixture to a 100 VAC~240 VAC 50/60 Hz power source. You must ensure that you correctly identify Line, Neutral and Earth feeds from the home, and that these are installed in the correct terminals. If no Earth wire is present, DO NOT INSTALL. Contact a qualified electrician.
WARNING! Ensure the use of correct mounting hardware for the installation. If the included mounting hardware is not suitable for your junction box, purchase a suitable junction box. Junction box replacement may require professional installation.
More than one disconnect switch may be required to turn off power to the equipment before servicing. Perform safe isolation of the circuit before commencing installation. The disconnect device for this equipment shall be provided as part of the building installation and in a readily accessible location.
WARNING! Ensure all power cables are rated for the location they are in according to applicable local electrical code, and that mechanical protection is used to prevent the cable from becoming cut. Ensure cables are securely clamped to the bracket, but do not over tighten.
PROTECTION AGAINST WATER
If your hardwired kit is dropped or otherwise damaged, the waterproofing of the hardwired kit may be compromised.
PRODUCT SPECIFICATIONS Hardwired Kit Model Number: 5F87E9 Electrical Rating: Input: 100-240V ~ 0.6A 50/60Hz Output: 5V⎓ 3A / 9V⎓ 2A Operating Temperature Range: -20°C to 50°C FOR USA CUSTOMERS Supplier’s Declaration of Conformity Hardwired Kit Model: 5F87E9
Responsible Party and Party issuing Supplier’s Declaration of Conformity: Ring LLC, 12515 Cerise Ave Hawthorne, CA, 90250 U.S.A. www.ring.com / legal@ring.com
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help.
Caution, pursuant to Section 15.21 of the FCC rules, user changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
RECYCLING YOUR DEVICE PROPERLY In some areas, the disposal of certain electronic devices is regulated. Make sure you dispose of, or recycle, your device in accordance with your local laws and regulations. For information about recycling your device, go to www.amazon.com/devicesupport.
ADDITIONAL SAFETY AND COMPLIANCE INFORMATION Additional safety, compliance, recycling and other important information regarding your device can be found at: www.ring.com/legal
TERMS AND POLICIES By purchasing or using the product, you agree to the Terms of Service found at ring. com/terms. For other applicable policies, visit ring.com/legal.
LIMITED WARRANTY FOR US AND CANADIAN CUSTOMERS For information on the Limited Warranty, visit ring.com/legal.