Ring Bridge mounted to wall inside a modern home

Safety and Compliance Information for Smart Lighting Bridge

Use Responsibly. Read all instructions and safety information before use.


Smart Lighting Bridge is for indoor use only.

Maintaining Your Smart Lighting Bridge

Do not expose your device or adapter to liquids. If your device or adapter gets wet, carefully unplug all cables without getting your hands wet and wait for the device and adapter to dry completely before plugging them in again. Do not attempt to dry your device or adapter with an external heat source, such as a microwave oven or a hair dryer. If the device or adapter appear damaged, discontinue use immediately. Use only accessories supplied with the device to power your device. To avoid risk of electric shock, do not touch your device or any wires connected to your device during a lightning storm.

Do not attempt to clean or polish your adapter with or expose your adapter to oil, lotion, or other abrasive substances.

Use only accessories supplied with your device, or specifically marketed for use with your device, to power your device. Use of third-party accessories may impact your device’s performance. In limited circumstances, use of third-party accessories may void your device’s limited warranty. In addition, use of incompatible third-party accessories may cause damage to your device or the third-party accessory. Read all safety instructions for any accessories before using with your device.

Use this device in dry rooms only. Do not cover the device while operating. Do not open the housing. Protect this device from sunlight. Disconnecting the plug will power the device off. Do not use the device if the plug or housing is defective, there is a risk of electric shock.

Servicing Your Device

If your device needs service, please contact Ring Customer Support.

Faulty service may void the warranty.

Other Safety Considerations

• Do not force the adapter into a power outlet.

• Do not expose the adapter or cable to liquids.

• If the adapter or cable appears damaged, discontinue use immediately.

Install your power adapter into an easily accessible socket-outlet located near the equipment that will be plugged into or powered by the adapter.

Using Your Device Around Other Electronic Devices

Your device generates, uses, and can radiate radio frequency (RF) energy and, if not used in accordance with its instructions, may cause interference to radio communications and electronic equipment. External RF signals may affect improperly installed or inadequately shielded electronic operating systems, entertainment systems, and personal medical devices. While most modern electronic equipment is shielded from external RF signals, if in doubt, check with the manufacturer. For personal medical devices (such as pacemakers and hearing aids), consult with your physician or the manufacturer to determine if they are adequately shielded from external RF signals.

FCC Compliance Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Note: This Product has been tested and found to comply with the limits for a Class B digital device or external switching power supply, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. The Products generate, use and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

-Reorient or relocate the receiving antenna.

-Increase the separation between the equipment and receiver.

-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

-Consult the dealer or an experienced radio/TV technician for help.

Pursuant to Section 15.21 of the FCC rules, changes or modifications to a Product by the user that are not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

The device meets the FCC Radio Frequency Emission Guidelines and are certified with the FCC. Information on these Products is on file with the FCC and can be found by inputting such Product's FCC ID (which can be found on the device) into the FCC ID Search form available at https://www.fcc.gov/oet/ea/fccid

The party responsible for FCC compliance is Ring LLC, 1523 26th St, Santa Monica, CA 90404 USA

If you wish to contact Amazon visit www.amazon.com/devicesupport, select United States, click Help & Troubleshooting, then scroll to the bottom of the page and under the Talk to an Associate option, click on Contact Us.

Information Regarding Exposure to Radio Frequency Energy

The output power of the radio technology used in the Products is below the radio frequency exposure limits set by the FCC.

This device should be installed and operated with a minimum distance of 20 cm between the radiator and your body.

Recycling Your Device Properly

In some areas, the disposal of certain electronic devices is regulated. Make sure you dispose of or recycle the device in accordance with your local laws and regulations. For information about recycling, go to www.amazon.com/devicesupport.

Product Specifications

Model No.: [5B01S8]

Input: 120V ~ 50/60Hz

Output:[ 5]V ⎓[1]A

Operating temperature: 0 - 48.5C (32- 120F)

Additional Information

You can find the Terms of Use, Limited Warranty, instructions for using the device, Customer Service contact information, and other applicable terms and device information at Ring.com.

Last updated 5 months ago