How To Change Replaceable Batteries for Ring Smart Lighting Devices

Ensure your home is always illuminated by learning how to replace the batteries in your Ring Smart Lighting devices to keep them up and running.

Before changing the replaceable battery in your Ring Smart Lighting device, be sure to:

• Check for old batteries that may be out of power or if you have batteries from a different brand installed.
• Swap out existing batteries for new ones to ensure your device is performing at its best, even if you think your current batteries might be fresh.
• Get the most out of your battery with these

  helpful tips and trick on how to to maximize battery life and reduce the number of unwanted motion alerts

  .

Mailbox Sensor Battery

What you’ll need before replacing the batteries in your Mailbox Sensor:

• Mailbox Sensor.
• Three (3) AAA batteries (sold separately).

To replace your Mailbox Sensor batteries:

1. Pull the tabs on the sides of the Mailbox Sensor apart to remove the rear cover.
2. Pull the cover off.
3. Insert the three (3) AAA batteries into the sensor.
4. Follow the corresponding marking to make sure the batteries are inserted the right way.
5. Snap the cover back onto the Mailbox Sensor.
6. Mount your Mailbox Sensor back into your mailbox.

Motion Sensor Battery

What you’ll need before replacing the batteries in your Motion Sensor:

• Motion Sensor.
• Three (3) AAA batteries (sold separately).

To replace your Motion Sensor batteries:

1. Pull the tabs on the sides of the Motion Sensor outward to remove the front cover.
2. Insert three (3) AAA batteries, matching the flat ends with the springs.
3. Snap the cover back onto the Motion Sensor.
4. Mount your Motion Sensor back into place.

Steplight Battery

What you’ll need before replacing the batteries in your Steplight:

• Steplight.
• Three (3) C-Cell batteries (sold separately).
• Flathead screwdriver.

To replace your Steplight batteries:

1. Using a flathead screwdriver, remove the screws from the back and lift off the battery lid.
2. Remove the screws from the Steplight’s back cover.
   1. Place the screws in a safe spot to be used later.
3. Insert the three (3) C-Cell batteries, matching the flat ends with the springs.
4. Screw the back cover on.
5. Mount the Steplight back in place.

Spotlight Battery

What you’ll need before replacing the batteries in your Spotlight:

• Spotlight.
• Four (4) D-Cell batteries (sold separately).

To replace your Spotlight batteries:

1. Remove the locking screw to release the Spotlight from its mounted position.
2. Place the screw in a safe spot to be used later.
3. Twist and pull off the front of the light
4. Press the buttons on the top and bottom of the battery compartment to open.
5. Insert four (4) D-Cell batteries, matching the flat ends with the springs.
6. Line up the arrows on the lid and compartment.
7. Press down to snap the lid back on.
8. Mount the Spotlight back in place and replace and tighten the locking screw.

Pathlight Battery

What you’ll need before replacing the batteries in your Pathlight:

• Pathlight.
• Four (4) D-Cell batteries (sold separately).

To replace your Pathlight batteries:

1. Push in the lock button and slide off the front cover of the Pathlight.
2. Insert the four (4) D-Cell batteries, flat end first.
3. Slide the cover back onto the Pathlight.
4. Twist your Pathlight back onto its stake counterclockwise until it clicks.

Floodlight Battery

What you’ll need before replacing the batteries in your Floodlight:

• Floodlight.
• Four (4) D-Cell batteries (sold separately).

To replace your Floodlight batteries:

1. Twist the Floodlight counter-clockwise to unlock the back cover.
2. Insert the four (4) D-Cell batteries, flat end first.
3. Twist the cover back onto the Floodlight.
4. Mount the Floodlight back in place.