Safety and Compliance Information for Ring Wired Doorbell Pro
Use Responsibly. Read all instructions and safety information before use.
FAILURE TO FOLLOW THESE SAFETY INSTRUCTIONS COULD RESULT IN FIRE, ELECTRIC SHOCK, OR OTHER INJURY OR DAMAGE!
WARNING: Electrical shock hazard. Disconnect power to installation area at your circuit breaker or fuse box before beginning installation. Always use caution when handling electrical wiring.
Installation by a qualified electrician may be required in your area. Refer to your local laws and building codes before performing electrical work; permits and/or professional installation may be required by law.
The disconnect device for this equipment shall be provided as part of the building installation and in a readily accessible location.
WARNING: The device and accessories may present a choking hazard to small children and pets. Keep them out of reach of small children and pets.
Your device can withstand outdoor use and has been tested to withstand water projected through a 6.3mm nozzle at a volume of 12.5 liters per minute and a pressure of 30 kPa at a distance of 3 meters for at least 3 minutes. However, your device is not intended for underwater use. To protect against electric shock, do not intentionally submerge or immerse your device, battery, or adapter (not included) in water or expose your device or adapter to other liquids. Do not spill any food or beverages on your device, battery, or adapter. Do not attempt to clean or polish your device, battery, or adapter with or expose your device, battery, or adapter to oil, lotion, or other abrasive substances. Do not expose your device, battery, or adapter to salt water or other conductive liquids. Do not expose your device, battery, or adapter to pressurized water, high velocity water, or extremely humid conditions (such as a steam room). If your device, battery, or adapter gets wet, carefully unplug all cables without getting your hands wet and wait for it to dry completely before plugging it in again. Do not attempt to dry your device, battery, or adapter with an external heat source, such as a micro- wave oven or a hair dryer. To avoid risk of electric shock, do not touch your device, battery, or adapter or any wires connected to your device during a lightning storm while your device, battery, or adapter is plugged in. If your device, battery, or adapter appears to be damaged, discontinue use immediately.
Users are required to use a power supply that complies with PS2orL.P.S.certification and approval. Use only accessories supplied with your device, or specifically marketed for use with your device, to power your device. Use of third-party accessories may impact your device’s performance. In limited circumstances, use of third-party accessories may void your device’s limited warranty. In addition, use of incompatible third party accessories may cause damage to your device or the third-party accessory. Read all safety instructions for any accessories before using with your device.
Protect the device from direct sunlight. Install the device at dry locations and protect it against rain and humidity. The device may not get contact to salt water or other conductive liquids. The device must be charged only within a building in a dry state.
SAFELY CONNECTING YOUR WIRED DOORBELL PRO (formerly RING VIDEO DOORBELL PRO 2) TO YOUR HOME’S ELECTRICAL WIRING
If you install the Wired Doorbell Pro (formerly Ring Video Doorbell Pro 2) where a doorbell is already in use and you connect the Wired Doorbell Pro (formerly Ring Video Doorbell Pro 2) to your home’s doorbell electrical wiring, you must turn off the existing doorbell’s power source at your home’s circuit breaker or fuse and test that the power is off BEFORE removing the existing doorbell, installing the Wired Doorbell Pro (formerly Ring Video Doorbell Pro 2), or touching electrical wires. Failure to turn off circuit breaker or fuse so could result in FIRE, ELECTRIC SHOCK, or OTHER INJURY or DAMAGE.
More than one disconnect switch may be required to turn off the equipment before servicing.
To test whether you have successfully de-energized your existing doorbell’s power source, press your doorbell several times to confirm that the power is off.
If the electrical wiring in your home does not resemble any of the diagrams or instructions provided with Wired Doorbell Pro (formerly Ring Video Doorbell Pro 2), if you encounter damaged or unsafe wiring, or if you are unsure or uncomfortable in performing this installation or handling electrical wiring, please consult a qualified electrician in your area.
Only use accessories & power sources with L.P.S. or PS2 certification that are recommended by the manufacturer. Use of third-party accessories may lead to damage to your Ring Video Doorbell Pro 2 or the accessory and may cause fire, electric shock, or injury.
Maintaining Your Wired Doorbell Pro (formerly Video Doorbell Pro 2)
Do not expose your device or adapter to liquids. If your device or adapter gets wet, carefully unplug all cables without getting your hands wet and wait for the device and adapter to dry completely before plugging them in again. Do not attempt to dry your device or adapter with an external heat source, such as a microwave oven or a hair dryer. If the device or adapter appear damaged, discontinue use immediately. Use only accessories supplied with the device to power your device. To avoid risk of electric shock, do not touch your device or any wires connected to your device during a lightning storm.
Only handle your device with clean hands. Clean the device by unplugging it and using a soft cloth that is slightly damp with water and a touch of rubbing alcohol; be careful not to wipe it with anything abrasive or to use any harsh chemicals. After cleaning, wait for the device to dry completely before plugging it in again.
Don't expose your device to steam, extreme heat or cold. For example, do not install your device near any heat sources such as space heaters, heater vents, radiators, stoves, or other things that produce heat. Use your device in a location where temperatures remain within the device’s operating temperature range set forth in this guide. Your device may get warm during normal use. To reduce the effect of the warming, place your device on a heat resistant surface.
Use only accessories supplied with your device, or specifically marketed for use with your device, to power your device. Use of third-party accessories may impact your device’s performance. In limited circumstances, use of third-party accessories may void your device’s limited warranty. In addition, use of incompatible third-party accessories may cause damage to your device or the third-party accessory. Read all safety instructions for any accessories before using with your device.
Your device can withstand outdoor use and contact with water under certain conditions. However, your device is not intended for underwater use and may experience temporary effects from exposure to water. Do not intentionally immerse your device in water or expose it to liquids. Do not spill any food, oil, lotion, or other abrasive substances on your device. Do not expose your device to pressurized water, high velocity water, or extremely humid conditions (such as a steam room). To protect against electric shock, do not place cord, plug, or device in water or other liquids.
Other Safety Considerations
• Do not expose the adapter or cable to liquids.
• If the adapter or cable appears damaged, discontinue use immediately.
Using Your Device Around Other Electronic Devices
Your device generates, uses, and can radiate radio frequency (RF) energy and, if not used in accordance with its instructions, may cause interference to radio communications and electronic equipment. External RF signals may affect improperly installed or inadequately shielded electronic operating systems, entertainment systems, and personal medical devices. While most modern electronic equipment is shielded from external RF signals, if in doubt, check with the manufacturer. For personal medical devices (such as pacemakers and hearing aids), consult with your physician or the manufacturer to determine if they are adequately shielded from external RF signals.
Product Specifications
Device Name: Wired Doorbell Pro (formerly Video Doorbell Pro 2)
Model Number: 5AT2S2
Electrical Rating: 16–24 VAC, 40VA max, 50/60Hz Temperature Rating: -5°F to 120°F (-20°C to 50°C)
RECYCLING YOUR DEVICE PROPERLY
In some areas, the disposal of certain electronic devices is regulated. Make sure you dispose of, or recycle, your device in accordance with your local laws and regulations. For information about recycling your device, go to www.amazon.com/devicesupport. For information regarding Amazon’s recycling program, visit https://amazonrecycling-us.re-teck.com/recycling/home.
Terms of Service and Warranty
By purchasing or using the product, you agree to the Terms of Service found at ring.com/terms
For information on our warranty, theft protection, and Ring Plans, see ring.com/legal
FCC Compliance Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Pursuant to Section 15.21 of the FCC rules, changes or modifications to a Product by the user that are not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
The device meets the FCC Radio Frequency Emission Guide- lines. Information on the product is on file with the FCC and can be found by inputting such Product’s FCC ID (which can be found on the device) into the FCC ID Search form avail- able at fcc.gov/oet/ea/fccid.
The party responsible for FCC compliance is:
Ring LLC, 12515 Cerise Ave, Hawthorne, CA 90250, USA
FCC Radiation Exposure Statement
This device complies with FCC radiation exposure limits set forth for an uncontrolled environment and it also complies with Part 15 of the FCC RF Rules. This equipment must be installed and operated in accordance with provided instructions and the antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. End-users and installers must be provided with antenna installation instructions and consider removing the no-col- location statement.
Information Regarding Exposure to Radio Frequency Energy
The output power of the radio technology used in the Products is below the radio frequency exposure limits set by the FCC.
This device should be installed and operated with a minimum distance of 20 cm between the radiator and your body.
Product Specifications
Model No.: 5AT2S2
Input: 16-24 VAC/24VDC
Operating temperature: -5°F to 120°F (-20°C to 50°C)
Connectivity: 802.11 a/b/g/n/ac @2.4GHz and 5.0GHz