Safety and Compliance Information for Smart Lighting PAR38 Smart LED Bulb
Use Responsibly. Read all instructions and safety information before use.
FAILURE TO FOLLOW THESE SAFETY INSTRUCTIONS COULD RESULT IN FIRE, ELECTRIC SHOCK, OR OTHER INJURY OR DAMAGE
WARNING: Risk of electrical shock. Do not attempt to open or disassemble the bulb.
Not suitable for use with standard wall dimmers. Suitable for Wet Locations.
This device is not intended for use with emergency exit fixtures or emergency lights.
Before replacing, turn off power and let the bulb cool to avoid electrical shock or burn.
Not for use in totally enclosed fixtures. Suitable for open fixtures only.
Dispose of this device in accordance with disposal laws in your area.
Not compatible with photo sensors, motion sensors or timers unless specifically designed for Ring Smart Lighting.
OPERATING INSTRUCTIONS:
Use the bulb only in a socket rated for this bulb.
This device is not a toy designed to be played with by children.
Do not place the device on hot surfaces.
Turn off power before inspection, installation, or removal. Do not force bulb into incompatible bulb holder.
Your bulb can withstand outdoor use. However, your bulb is not intended for underwater use. To protect against electric shock, do not intentionally submerge or immerse your bulb in water or expose your bulb to other liquids. Do not spill any food or beverages on your bulb. Do not attempt to clean or polish your bulb with or expose your device to oil, lotion, or other abrasive substances. Do not expose your bulb to pressurized water, high velocity water, or extremely humid conditions (such as a steam room). Do not attempt to dry your bulb with an external heat source, such as a microwave oven or hair dryer. If your bulb appears to be damaged, discontinue use immediately.
For safety reasons, do not open devices, which will also void the warranty.
Servicing Your Device
If your device needs service, please contact Ring Customer Support.
Using Your Device Around Other Electronic Devices
Your device generates, uses, and can radiate radio frequency (RF) energy and, if not used in accordance with its instructions, may cause interference to radio communications and electronic equipment. External RF signals may affect improperly installed or inadequately shielded electronic operating systems, entertainment systems, and personal medical devices. While most modern electronic equipment is shielded from external RF signals, if in doubt, check with the manufacturer. For personal medical devices (such as pacemakers and hearing aids), consult with your physician or the manufacturer to determine if they are adequately shielded from external RF signals.
FCC Compliance Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Note: This Product has been tested and found to comply with the limits for a Class B digital device or external switching power supply, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. The Products generate, use and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Pursuant to Section 15.21 of the FCC rules, changes or modifications to a Product by the user that are not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
The device meets the FCC Radio Frequency Emission Guidelines and are certified with the FCC. Information on these Products is on file with the FCC and can be found by inputting such Product's FCC ID (which can be found on the device) into the FCC ID Search form available at https://www.fcc.gov/oet/ea/fccid
The party responsible for FCC compliance is Ring LLC 1523 26th St, Santa Monica, CA 90404 USA
If you wish to contact Amazon visit www.amazon.com/devicesupport, select United States, click Help & Troubleshooting, then scroll to the bottom of the page and under the Talk to an Associate option, click on Contact Us.
Device Name: Smart Lightbulb (PAR38)
Model: 5AT1S4
Information Regarding Exposure to Radio Frequency Energy
The output power of the radio technology used in the Products is below the radio frequency exposure limits set by the FCC.
This device should be installed and operated with a minimum distance of 20 cm between the radiator and your body.
Recycling Your Device Properly
In some areas, the disposal of certain electronic devices is regulated. Make sure you dispose of or recycle the device in accordance with your local laws and regulations. For information about recycling, go to www.amazon.com/devicesupport.
Product Specifications
Model No.: 5AT1S4
Input: 120VAC, 150mA, 16W, 60Hz
Operating temperature: -4 to 104F (-20 to 40C)
Additional Information
You can find the Terms of Use, Limited Warranty, instructions for using the device, Customer Service contact information, and other applicable terms and device information at Ring.com.