Zoekresultaten
Resultaten tonen voor space
Zoek in plaats daarvan op spade
Installing your Hardwired Transformer Kit
Be careful of damaging walls: Removing and installing your transformer may involve removing your old doorbell mechanism or pulling the transformer from inside a crawl space. Lack of care may cause damage to walls or other structural portions of the house. Be careful of damaging other electrical components: It's possible that your original transformer may be mounted in a basement, attic, or crawl space with other electrical components. Be careful when removing the transformer that you do not pull or otherwise damage these other components. Click here for more information on a hardwired transformer.
De Outdoor Cam Pro Plug-In installeren
اختر موقع Outdoor Cam Pro | 3 Flat installation / Installation auf einer ebenen Fläche / Installation à plat / Installazione su un piano / Instalación en superficies planas / Neerzetten op vlakke ondergrond / Flat montering / Montering på plan yta / Asennus tasaiselle pinnalle / Plan montering / تركيب مسطح 1. Place your camera on a level surface with 5.5 in (14 cm) of space in every direction and plug in. / Stellen Sie die Kamera auf eine ebene Fläche mit 14 cm Abstand in alle Richtungen und schließen Sie sie an. / Placez votre caméra
De contactsensor van Ring Alarm installeren en gebruiken
cm (1”) between them. 4. Leave at least 1.3cm (1/2”) space around the Sensor so you can open the battery compartment. 5. Clean the area, then peel the backing from the mounting tape and press the Sensor and magnet into place. 6. To install using screws you will need: Screws: 4x 3x21mm. Anchors: 4x 5mm. If you’re using the Contact Sensor on a door you use often, choose Main Door as the placement option.
Technische informatie over Z-Wave voor Ring Alarm
Screws and anchors are also provided for more permanent mounting. Metal strap ties can be used but are not provided. 4. Follow the same steps for the companion magnet ensuring the magnet is aligned with the sensor and no more than 1 inch from sensor for the “closed” position. Note: Leave ~ ½ in. of space on the sensor side to ensure you can slide open the case when it’s time to change the batteries. Note: • This product can be operated in any Z-Wave network with other Z-Wave certified devices from other manufacturers.
De Ring Alarm-contactsensor voor buiten installeren en gebruiken
Screws and anchors are also provided for more permanent mounting. Metal strap ties can be used but are not provided. 4. Follow the same steps for the companion magnet ensuring the magnet is aligned with the sensor and no more than 1 inch from sensor for the “closed” position. Note: Leave ~ ½ in. of space on the sensor side to ensure you can slide open the case when it’s time to change the batteries. Note: • This product can be operated in any Z-Wave network with other Z-Wave certified devices from other manufacturers.
PoE+-adapter met beugel installeren
vom Stromanschluss der Kamera. / Retirez le capuchon en caoutchouc du port d’alimentation de votre caméra. / Rimuovere il tappo di gomma dalla porta di alimentazione della videocamera. / Retira el tapón de goma del puerto de alimentación de la cámara. / Verwijder de rubberen afdekking van de voedingspoort van je camera. / Fjern gummihetten fra kameraets strømport. / Ta bort gummiskyddet från kamerans strömport. / Irrota kumisuojus kameran virtaportista. / Fjern gummihætten fra kameraets strømport. / ل الغطاء المطاطي من منفذ الطاقة الخاص بالكاميرا ِ .أز NOTE: Store the rubber cap in a safe space.
Handleidingen voor Ring-apparaten
Wall installation 1. Slide the mounting plate in the direction opposite to the UP arrow to remove. 2. Use the mounting plate as a guide to mark screw holes on the wall with 5.5 in (14 cm) of space in every direction. 5.5 in (14 cm) 5.5 in (14 cm) 5.5 in (14 cm) 5.5 in (14 cm) Spotlight Cam (2nd Gen) | 3EN 3. Install the mounting plate with the UP arrow pointing up.On