Hands installing a Wired Doorbell 2K Plus on white wall.

Installing Wired Doorbell 2K Plus Plug-In

Safety and compliance information for Wired Doorbell 2K Plus

Download the user manual for Wired Doorbell 2K Plus Plug-InDownload the user manual for Wired Doorbell 2K Plus Plug-In (العربية)Download the user manual for Wired Doorbell 2K Plus Plug-In (Dansk)Download the user manual for Wired Doorbell 2K Plus Plug-In (Suomi)Download the user manual for Wired Doorbell 2K Plus Plug-In (Norsk)Download the user manual for Wired Doorbell 2K Plus Plug-In (Svenska)

Hardware included

Illustration to show screws, wall plugs and wire plugs included.

Tools included

Included Removal tool

Removal tool

Tools needed

Illustration of a cross point screwdriver needed for installation.

Phillips-head screwdriver

Illustration of a power drill to use as an installation tool.

Drill with a 1/4 in (6 mm) masonry bit (optional)

  1. Download the Ring app.
Illustration showing to download the Ring App on the mobile device.
  1. Scan the QR code.
Instruction stating to scan the applicable QR code to start a device set up in the Ring App.
  1. Remove the protective wrap.
Illustration indicating to remove the protective wrap from the Ring Camera.
  1. Choose a location for your doorbell.
Illustration to show optimal location for your doorbell, 1.2 metres from the ground.

Doorbell installation

  1. Without plugging in the power adapter, run the power cable from the outlet to where you're installing your doorbell.
Illustration to show the power cable going from the adapter to where you're installing your doorbell, without being plugged in.
  1. Secure the power cable with the included cable clips.

NOTE: If running the cable through a wall, door, or window, exercise caution for electrical wiring and pipes when drilling.

A cable secured with cable clips and screws labelled C and D.
  1. (Optional) If using a corner mount, install the mount over your doorbell wires using the large oval holes, ensuring it is facing in your desired viewing direction.

NOTE: Multiple corner mounts can be stacked together. We do not recommend more than two.

A corner mount being installed over the doorbell wires using screws labelled A to secure.

On stucco, brick, or concrete, use a 6 mm (1/4 in) masonry bit to drill holes for the included wall anchors.

Stucco, brick, and wood installation.

(Optional) If using a wedge mount, install the mount over your doorbell wires using the screws included with your wedge kit, ensuring it is facing down.

NOTE: Multiple wedge mounts can be stacked together. We do not recommend more than two.

A wedge mount being installed over the doorbell wires, using screws labelled A to secure.

On stucco, brick, or concrete, use a 6 mm (1/4 in) masonry bit to drill holes for the included wall anchors.

Stucco, brick, and wood installation.
  1. (Optional) If installing multiple wedge or corner mounts, insert screws through both mounts to hold them together.
Two corner mounts being stacked and held together using screws labelled A.
  1. Install the mounting bracket on your mount or directly over the doorbell wiring with the included screws.
A mounting bracket placed directly over the doorbell wiring with the included screws.
  1. Remove your doorbell's faceplate by inserting the removal tool into the slot at the bottom of your doorbell.
Diagram showing the use of the security tool to remove the faceplateDiagram with arrow pointing up to remove faceplate
  1. Connect the power cable to your doorbell's wire terminals.
The back of a doorbell showing the power cable attached to the doorbell's wire terminals.
  1. Mount your doorbell by hooking it over the bracket and pushing down.
Diagram showing directional arrows to indicate to hook the device and then press down to mount.
  1. Tighten the security screw.
Diagram showing the connection of wires to the doorbell terminalsCircular frame showing a close up of the security screw.
  1. Plug in the power adapter.
A plug-in adapter plugged into the wall, receiving power.
  1. Ring your doorbell to ensure everything is properly connected.
Illustration of the Wired Doorbell 2K Plus.
  1. Reattach the faceplate.
Diagram with arrow pointing down to replace the faceplate

Last updated 3 days ago
English (GB)Change
©2026 Ring LLC or its affiliates
|
||