Safety and compliance information for Access Control Unit V2

READ ALL SAFETY INFORMATION BEFORE USING THE DEVICE. FAILURE TO FOLLOW THESE SAFETY INSTRUCTIONS COULD RESULT IN FIRE, ELECTRIC SHOCK, OR OTHER INJURY OR DAMAGE.

This device should only be installed by a professional installer or licensed electrician. Refer to your local laws and building codes before performing electrical work; approvals, permits and/or professional installation may be required by law.

WARNING: Electrical shock hazard. Disconnect power to installation area at your circuit breaker or fuse box before beginning installation. Always use caution when handling electrical wiring.

Your device should only be used in accordance with the instructions and intended purpose. Using this device in any way other than its intended purpose could cause injury to yourself, others or damage to the device. Your device is not waterproof and as such should not be submerged in water, doing so could cause injury to yourself, others or damage to the device.

Do not force the adapter into a power outlet.

Install your power adapter into an easily accessible socket-outlet located near the equipment that will be plugged into or powered by the adapter.

Your device does not have an on/off button. If you wish to stop power from flowing to your device, unplug the power cord. Do not plug multiple electric devices into the same wall socket. Overloading a socket can cause it to overheat and may result in a fire.

Users are required to use a power supply that complies with PS2 or L.P.S. certification and approval.

Use only accessories supplied with your device, or specifically marketed for use with your device, to power your device. Use of third-party accessories may impact your device’s performance. In addition, use of incompatible third-party accessories may cause damage to your device or the third-party accessory. Read all safety instructions for any accessories before using with your device.

Don't expose your device to steam, extreme heat or cold. Use your device in a location where temperatures remain within the device’s operating temperature range set forth in this guide. Your device may get warm during normal use.

WARNING: Small parts contained in your device and its accessories may present a choking hazard to small children.

CAUTION: When mounting this device in elevated locations, use precautions to ensure that the device does not fall and harm bystanders.

If you install the Ring Access Control Unit V2 where an access control device is already in use and you connect the Ring Access Control Unit V2 to your building's access control device electrical wiring, you must turn off the existing access control device’s power source at your building’s circuit breaker or fuse and test that the power is off BEFORE removing the existing access control device, installing the Ring Access Control Unit V2, or touching electrical wires. Failure to turn off circuit breaker or fuse so could result in FIRE, ELECTRIC SHOCK, or OTHER INJURY or DAMAGE.

More than one disconnect switch may be required to turn off the equipment before servicing.

If the electrical wiring in your building does not resemble any of the diagrams or instructions provided with Ring Access Control Unit V2, if you encounter damaged or unsafe wiring, or if you are unsure or uncomfortable in performing this installation or handling electrical wiring, please consult a qualified electrician in your area.

Use this device in dry rooms only. Do not cover the device while operating. Do not open the housing. Protect this device from sunlight. Disconnecting the plug will power the device off. Do not use the device if the plug or housing is defective, there is a risk of electric shock.

Do not expose your device or adapter to liquids. If your device or adapter gets wet, carefully unplug all cables without getting your hands wet and wait for the device and adapter to dry completely before plugging them in again. Do not attempt to dry your device or adapter with an external heat source, such as a microwave oven or a hair dryer.

To reduce the risk of damage to your device, follow these instructions:

Do not immerse your device in water or expose them to seawater, salt water, chlorinated water or other liquids (such as beverages).

Do not spill any food, oil, lotion or abrasive substances on your device.

Do not expose your device to pressurised water, high-velocity water or extremely humid conditions (such as a steam room).

Model Number: 8KCEA3 (ecBAC-2)

USB 5V 0.8A

Terminal 10-24VAC 4W

Terminal 10-24VDC 4W

Operating Temperature Range: -40°C to 65°C

Model: 8KCEA3 (ecBAC-2)

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Responsible Party and Party issuing Supplier’s Declaration of Conformity:

Ring LLC, 12515 Cerise Ave Hawthorne, CA, 90250 U.S.A.

www.ring.com / legal@ring.com

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help.

Caution, pursuant to Section 15.21 of the FCC rules, user changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

This device complies with FCC radio frequency radiation exposure limits set forth for an uncontrolled environment. Information is on file with the FCC and can be found by inputting such Product’s FCC ID (which can be found on the device) into the FCC ID Search form available at

.

The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other product antenna or transmitter.

Model ecBAC-2 is a cellular/ethernet RJ45 cloud connected gateway to an Access Control Unit. The device is permanently mounted to a wall or in a call box from -20C to 50C in a dry environment.

This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada's licence-exempt RSS(s). Operation is subject to the following two conditions: (1) This device may not cause interference. (2) This device must accept any interference, including interference that may cause undesired operation of the device.

This equipment complies with IC RSS-102 RF exposure limits set forth for an uncontrolled environment.

This equipment should be installed and operated with a minimum distance of 20 cm between the radiator and your body.

CAN ICES (B)/NMB (B)

Hereby, Ring LLC declares that the radio equipment type 8KCEA3 (ecBAC-2) is in compliance with Directive 2014/53/EU and UK Radio Equipment Regulations 2017 (S.I. 2017/1206), including currently valid amendment(s). The full texts of the declarations of conformity and other applicable statements of compliance for this product are available at the following internet address:

Cellular

Using Quectel EG916Q-GL

LTE FDD

CAT1Bis: B1/B3/B7/B8/B20/B28/

LTE-TDD

CAT1Bis:B34/B38/B40/B41

Power Class 3

23 dBm @ LTE Bands

: The device enters networked standby mode less than one minute from the last user activity.

: The network connection is disabled when the ethernet cable is removed.

Power Adapter Model No. PS57CP

Manufacturer:

Ring LLC / Amazon EU S.à r.l., 38 Avenue John F. Kennedy, L-1855 Luxembourg / Amazon UK, 1 Principal Place, Worship Street, London, EC2A 2FA, United Kingdom

100–240V ~0.3A 50/60Hz

5.2V, 1.8A (9 watts)

Average Active Efficiency (%): 82.1

Efficiency at low load (10%): 79.0

No Load power consumption (W): 0.06

In order to protect human health, this device meets the thresholds for exposure of the general public to electromagnetic fields according to Council Recommendation 1999/519/EC.

This device should be installed and operated with at least 20 cm between the radiator and your body.

In some areas, the disposal of certain electronic devices is regulated. Make sure you dispose of, or recycle, your device in accordance with your local laws and regulations. For information about recycling your device, go to

.

Additional safety, compliance, recycling and other important information regarding your device can be found at: