Safety and compliance information for Hardwired Kit for Cameras
IMPORTANT PRODUCT INFORMATION
FAILURE TO FOLLOW THESE SAFETY INSTRUCTIONS COULD RESULT IN FIRE, ELECTRIC SHOCK, OR OTHER INJURY OR DAMAGE.
Watch for small parts! The device and accessories may present a choking hazard to small children. Keep them out of reach of small children.
Electrical shock hazard! Disconnect power to the installation area at your circuit breaker or consumer unit before beginning installation. Always use caution when handling electrical wiring. Installation and wiring must be performed by a licensed electrician in Australia and New Zealand, and may be required in other countries. Refer to your local laws and building codes before performing electrical work; permits and/or professional installation may be required by law.
Fire Risk! Do not mount near combustible or flammable surfaces.
SAFETY INFORMATION
Your device is water resistant and is suitable for outdoor use. However, your device is not intended for underwater use. To protect against electric shock, do not submerge or immerse your device or Hardwired Kit in water or expose your device or adapter to other liquids. Do not spill any food or beverages on your device or Hardwired Kit. Do not attempt to clean or polish your device or Hardwired Kit with or expose your device or Hardwired Kit to oil, lotion, or other abrasive substances. Do not expose your device or Hardwired Kit to salt water or other conductive liquids. Do not expose your device or Hardwired Kit to pressurized water, high velocity water, or extremely humid conditions (such as a steam room). Do not attempt to dry your device or Hardwired Kit with an external heat source, such as a microwave oven or a hair dryer. To avoid risk of electric shock, do not touch your device or any wires connected to your device during a lightning storm while your device is powered. If your device or Hardwired Kit appears to be damaged, discontinue use immediately.
Do not install on the ground. Your device can be installed indoors or outdoors and should be installed on either a wall or eave. Do not cover the device while operating. Do not open the housing. Your device does not contain serviceable parts. Disconnecting the wires will power the device off. Do not use the device if the wires or housing are defective, as there is a risk of electric shock. Do not cut any wires with factory installed wire connectors or remove the wire connectors.
Do not install on circuits feeding motor loads such as kitchen appliances, HVAC equipment, washer / dryer or garage door openers. Do not install when it is raining. Following periods of extended use, the device may feel hot to touch. Please wait 30 minutes after the device is no longer in use before touching or moving.
Only use accessories that are recommended by the manufacturer. Use of third-party accessories may lead to damage to your device or the accessory and may cause fire, electric shock, or injury. Handle your device and its accessories with care. Your device or its accessories may have pointed edges which can lead to scratches, cuts, or other physical injury.
SAFELY CONNECTING YOUR CAMERA TO YOUR HOME’S ELECTRICAL WIRING
Warning! You must disconnect the power source at the home’s circuit breaker or consumer unit and test that the power is off BEFORE removing an existing light fixture, installing the device, or touching electrical wires. It is extremely important to adhere to this safety precaution, especially if any natural gas, petrol fumes, or other potentially explosive fumes may be present in the vicinity. Failure to turn off circuit breaker or consumer unit could result in EXPLOSION, FIRE, ELECTRIC SHOCK, DEATH, OTHER INJURY or PROPERTY DAMAGE.
BEFORE installing the device, review the diagrams and instructions provided. If the electrical wiring in the home does not resemble any of these diagrams or instructions, if you encounter damaged or unsafe wiring, or if you are unsure or uncomfortable in performing this installation or handling mains electrical wiring, please consult a qualified electrician. Verify that the supply voltage is correct. Connect fixture to a 100 V AC~240 V AC 50/60 Hz power source. You must ensure that you correctly identify Line, Neutral and Earth feeds from the home, and that these are installed in the correct terminals. If no Earth wire is present, DO NOT INSTALL. Contact a qualified electrician.
Warning! Ensure the use of correct mounting hardware for the installation surface. If the included mounting hardware is not suitable, purchase suitable hardware. More than one disconnect switch may be required to turn off power to the equipment before servicing. Perform safe isolation of the circuit before commencing installation. The disconnect device for this equipment shall be provided as part of the building installation and in a readily accessible location.
Warning! Ensure all power cables are rated for the location they are in according to applicable local electrical code, and that mechanical protection is used to prevent the cable from becoming cut. Ensure cables are securely clamped to the bracket, but do not over tighten.
Product Specifications
Device Name: Hardwired Kit for Cameras
Model Number: 5F87E9
Input Rating: 100-240 VAC, 50/60 Hz, 0.6A
Output Rating: 5.0 V DC, 3 A, 15.0 W; 9.0 V DC, 2.0 A, 18.0 W
Operating Temperature Range: -20 °C to 50 °C
Power Adapter Energy Efficiency Information – Europe
Input Voltage: 100–240 V ~
Input AC current: 0.6 A
Input AC Frequency: 50/60 Hz
Output Voltage: 5 VDC/ 9 V DC
Output Current: 3A/ 2 A
Output Power: 15W/ 18W
Average Active Efficiency: 84.98%/ 88.35%
Efficiency at Low Load (10%): 84.5%/ 84.47%
No-Load Power Consumption: 0.049 W
RECYCLING YOUR DEVICE PROPERLY
In some areas, the disposal of certain electronic devices is regulated. Make sure you dispose of, or recycle, your device in accordance with your local laws and regulations. For information about recycling your device, go to www.amazon.com/devicesupport.